Home > 62200-series > 62202 Bearing

62202 Deep Groove Ball Bearing 15×35×14mm | RHD Bearings

The tall drink of water in the bearing family - stretched for performance.

Meet the 62202: With 779kg (7.65kN) of engineering excellence and 15mm precision, this bearing delivers the perfect blend of personality and performance for your critical applications. The most widely used bearing in electronics, small motors, and precision instruments.

15mm
Bore Diameter
35mm
Outer Diameter
14mm
Width
7.65 kN
Load Rating
779 Kg
Load Capacity
0.06 Kg
Weight
Technical Specifications Applications 📞 Call +91-9702081858
62202 Bearing 15×35×14mm - RHD Bearings

62202 BEARING SPECIFICATIONS

Precision-engineered for reliability and performance

🔍 Common Search Terms

62202 bearing dimensions 15mm bore slim-fit bearing high-speed bearing 15mm shaft slim-profile bearing 62202 bearing specifications

📏Dimensions

d - ID (Bore Diameter)
15mm
D - OD (Outer Diameter)
35mm
B - Width
14mm
d₁ - Shoulder Diameter
≈21.7mm
D₂ - Recess Diameter
≈30.35mm
r₁,₂ - Chamfer Radius
min. 0.6mm
62202 Bearing: 15 × 35 × 14mm

Bearing Cross-Sectional View

62202 Deep Groove Ball Bearing Technical Drawing

⚡Load Ratings

Dynamic Load (Cr) 7.65kN
Static Load (Cor) 1.8kN
Load Capacity (kN) 7.65kN
Load Capacity (kg) 779kg

ðŸ’ĄWhat This Means

Dynamic Load (7.65kN): Maximum force while rotating. Exceeding this causes rapid wear and failure within hours.
Static Load (1.8kN): Maximum force when stationary. Use 80% for safety.
Calculate Your Load: Measure shaft forces, belt tensions, or gear loads. Include shock/vibration factors.
Failure Warning: Overloading causes bearing raceways to crack and balls to flatten permanently.

🔄Speed Limits

Grease Lubrication 19000 RPM
Oil Lubrication 23000 RPM
RHD Z2V2 Bearings 1400 RPM
RHD Z3V3 Bearings 2880 RPM
RHD Z4V4 Bearings 6000+ RPM

ðŸ’ĄWhat This Means

Grease Limit (19000 RPM): Heat generation increases exponentially above this. Grease breaks down, causing seizure.
Oil Advantage (23000 RPM): Better heat dissipation allows higher speed. Required for high-speed spindles.
Safe Operating Speed: Use 90% of limit (17100 RPM) for maximum L10 life of 10,000+ hours.
Failure Mode: Exceeding speed causes cage failure, ball skidding, and catastrophic overheating within minutes.

🔧Material & Quality

Steel Grade SAE52100
Ball Grade G10
Carbon Content 0.95-1.05%
Chromium Content 1.40-1.65%
ISO Standard 15:2011 Compliant

ðŸ’ĄWhat This Means

SAE52100 Chrome Steel: Premium bearing steel - harder than tool steel
G10 Balls: Ultra-precision balls with Âą0.25Âĩm tolerance
High Carbon: Superior hardness and wear resistance
Chromium: Adds corrosion resistance and toughness
ISO Standard: Fits any 62202 application worldwide

📊Vibration Classes

V2 Grade
Low: 110 Ξm/s
Med: 78 Ξm/s
High: 60 Ξm/s
V3 Grade
Low: 65 Ξm/s
Med: 46 Ξm/s
High: 35 Ξm/s
V4 Grade
Low: 52 Ξm/s
Med: 18 Ξm/s
High: 18 Ξm/s

ðŸ’ĄWhat This Means

V2 Grade: Standard grade - good for general applications
V3 Grade: Low vibration - like a smooth car engine
V4 Grade: Ultra-smooth - for precision instruments
Frequency Bands: Measured across different rotation speeds

🔇Noise Levels

Z2 Grade < 41 dB
Z3 Grade < 36 dB
Z4 Grade (Quiet) < 31 dB
Application Precision Equipment

ðŸ’ĄWhat This Means

Z2 Grade: Quiet as a library - good for most applications
Z3 Grade: Very quiet - like a whisper (40 dB = normal whisper)
Z4 Grade: Ultra-quiet - perfect for bedroom fans, medical equipment
Application: Ideal for sensitive environments

⚙ïļInternal Clearance

C2 (Tight) 0-9 Ξm
C0 (Normal) 3-18 Ξm
C3 (Loose) 11-25 Ξm
C4 (High Temp) 18-33 Ξm
C5 (Extra High Temp) 25-45 Ξm

ðŸ’ĄWhat This Means

C2 (Tight): Precision applications - less play, more accurate
C0 (Normal): Standard choice - works for most applications
C3 (Loose): Better for hot environments - allows thermal expansion
C4 (Exta Loose): Hot or tight-fit setups — extra room for thermal expansion.
C5 (Max Loose): Extreme heat/tight fits or near-limit speeds — maximum expansion allowance

SEAL OPTIONS

Choose the right protection for your application

62202-ZZ

Most Popular

Double metal shields

Speed Factor: 0.9 (17100 RPM)
Protection: Dust protection
Lubrication: Sealed for life

When to Use 62202-ZZ

Best For: Electronics, small motors, skateboards, general machinery
Conditions: Dry environments, moderate dust, precision applications
Achieves: Excellent balance of speed and protection for most applications
Avoid When: Heavy water exposure, chemical environments, food processing

62202-2RS

Protected

Double rubber seals

Speed Factor: 0.7 (13300 RPM)
Protection: Moisture and dust
Lubrication: Sealed for life

When to Use 62202-2RS

Best For: Outdoor applications, appliances, automotive systems, dirty environments
Conditions: Moisture, dust, contamination, washdown areas, food processing
Achieves: Maximum protection and zero maintenance requirements
Trade-off: Lower speed limit but superior environmental protection

62202

High Speed

Open bearing, no seals

Speed Factor: 1.0 (19000 RPM)
Protection: None
Lubrication: External required

62202-Z

Balanced

Single metal shield

Speed Factor: 0.95 (18050 RPM)
Protection: Light dust protection
Lubrication: Pre-greased

62202-RS

Protected

Single rubber seal

Speed Factor: 0.8 (15200 RPM)
Protection: Moisture and dust
Lubrication: Pre-greased, sealed

APPLICATIONS

Precision performance across industries

Drive Solutions

  • Paper feeder spindles
  • 3D printer z-axis drives
  • Small conveyor ends
  • Workshop vent fans
  • Cash register printer drums
  • Pneumatic valve motors
  • Ticketing mechanism gearboxes
  • Miniature machine feeders

Key Requirements: 15mm shaft with 5.5kN (≈560kg) dynamic load, 12,500 RPM grease, 35x14mm high-rotation components

Servo Modules

  • Servo robotic grippers
  • Measurement tape retractors
  • Digital lock actuators
  • Toy car steering units
  • Microscope focus drives
  • Small valve guides
  • Inspection camera pivots
  • Electronic drum rotors

Key Requirements: 15mm bore, 3.2kN (≈325kg) static load, supports precise positioning

Food Handling

  • Kitchen slicer blades
  • Bread maker shafts
  • Portable juicer drives
  • Compact mixing paddles
  • Nutrition scale cradles
  • Beverage machine arms
  • Chocolate coating rotors
  • Miniature shredders

Key Requirements: 15mm bore, 14mm width, cleanable, oil/grease suitable

Compatible Models & Shaft Requirements

Find bearings with the same bore size and ensure proper shaft preparation

🔄Related Models

6202 (15×35×11mm) 6302 (15×42×13mm) 6802 (15×24×5mm) 6902 (15×28×7mm)

🔧Shaft Requirements

Nominal Diameter 15.000mm
Tolerance Grade h6 (14.989-15.000mm)
Surface Finish Ra 0.8Ξm max
Runout Tolerance 0.013mm max

ðŸŽŊApplication-Specific Options

High Temperature: C3 clearance recommended
High Speed: RHD V3 & V4 bearings recommended
Corrosive Environment: SS (Stainless Steel) bearings recommended

Professional Expertise & Standards

Technical insights from 20+ years of bearing engineering and manufacturing excellence

📋ISO Compliance

ISO 15:2011 compliant dimensions ensure interchangeability with global bearing standards and seamless replacement in existing equipment.

🔎Material Science

Gcr15 chrome steel composition optimized for slim-fit bearing applications, providing superior hardness, wear resistance, and fatigue life.

⚙ïļPrecision Engineering

C0 clearance standard for most applications, C3 available for high-temperature use. h6 shaft tolerance recommended for optimal performance.

🔧Professional Installation

Professional installation required for maximum 50,000-hour service life. Proper tools and techniques prevent 80% of premature failures.

📊Performance Comparison

Slim-fit 14mm width with 7.65kN load capacity. Superior Gcr15 steel vs. standard steel in competing products.

💰Value Engineering

Best value in slim-fit bearing category for 7.65kN performance. Quality bearings last 3-10x longer than cheap alternatives, reducing total cost of ownership.

FREQUENTLY ASKED QUESTIONS

Expert guidance for 62202 bearing applications

Bearing Selection & Replacement ▾

What shaft tolerance is recommended for 62202 bearing installation?

h6 tolerance grade (14.989-15.000mm) provides optimal fit and performance for 62202 bearings.
Why This Matters
Proper shaft tolerance ensures correct interference fit, preventing slippage while allowing thermal expansion.
How To Handle It
Measure shaft diameter with precision calipers, ensuring it falls within h6 tolerance range before installation.
Use h6 tolerance for standard applications, h5 for high-precision requirements, and h7 for loose fits.

Can I replace a 62202 bearing with a different size bearing?

No, 62202 bearings have unique 15×35×14mm dimensions and cannot be replaced with other sizes without mechanical modifications.
Why This Matters
Bearing dimensions are critical for proper fit, load distribution, and system performance.
How To Handle It
Always use exact 62202 replacement or consult engineering specifications for alternative solutions.
Keep spare 62202 bearings in stock to avoid production delays and ensure consistent quality.

What load capacity does the 62202 bearing provide?

62202 bearing offers 780.3kg (7.65kN) dynamic load capacity and 1.80kN static load capacity, suitable for slim-fit applications requiring high performance.
Why This Matters
Load capacity determines bearing suitability for specific applications and operating conditions.
How To Handle It
Calculate actual application loads and ensure they remain within 780.3kg (7.65kN) dynamic limit with appropriate safety factors.
Use 62202 bearings for applications requiring up to 780kg load capacity with standard safety margins.
Installation & Maintenance ▾

What lubrication is required for 62202 bearings?

62202 bearings require grease lubrication for standard applications, with 19,000 RPM capability under proper lubrication conditions.
Why This Matters
Proper lubrication reduces friction, prevents wear, and extends bearing service life significantly.
How To Handle It
Apply high-quality bearing grease during installation and maintain regular lubrication intervals based on operating conditions.
Use lithium-based grease for general applications and synthetic grease for high-temperature or high-speed operations.

How do I properly install a 62202 bearing?

Install 62202 bearings using proper bearing installation tools, ensuring even pressure distribution and avoiding damage to bearing surfaces.
Why This Matters
Proper installation prevents premature failure, ensures optimal performance, and maintains dimensional accuracy.
How To Handle It
Use bearing heaters for interference fits, apply force evenly, and verify proper seating after installation.
Professional installation tools prevent 80% of premature bearing failures and ensure maximum service life.

What maintenance schedule is recommended for 62202 bearings?

62202 bearings require regular inspection every 3-6 months, with lubrication replenishment based on operating hours and conditions.
Why This Matters
Regular maintenance prevents unexpected failures, maintains performance, and extends bearing lifespan.
How To Handle It
Establish maintenance schedules based on operating conditions, document all maintenance activities, and monitor bearing condition regularly.
Implement predictive maintenance using vibration analysis to detect issues before they cause failures.
Troubleshooting & Problem Solving ▾

What causes premature failure in 62202 bearings?

Common causes include improper installation, inadequate lubrication, contamination, excessive loads, and misalignment.
Why This Matters
Understanding failure causes helps prevent future issues and improves system reliability.
How To Handle It
Implement proper installation procedures, maintain clean environments, ensure adequate lubrication, and monitor operating conditions.
80% of premature failures are preventable through proper installation and maintenance practices.

How do I identify bearing wear in 62202 bearings?

Signs of wear include increased noise, vibration, temperature rise, and reduced performance in 62202 bearings.
Why This Matters
Early detection of wear prevents catastrophic failures and allows for planned replacement.
How To Handle It
Monitor bearing condition regularly, use vibration analysis equipment, and establish baseline performance measurements.
Implement condition monitoring systems to detect wear patterns before they affect system performance.

What should I do if a 62202 bearing fails unexpectedly?

Immediately stop operation, inspect for damage, identify root cause, and replace with properly installed new bearing.
Why This Matters
Quick response prevents secondary damage and minimizes production downtime.
How To Handle It
Document failure details, analyze root causes, implement corrective actions, and maintain spare bearings for critical applications.
Keep detailed failure records to identify patterns and prevent similar issues in the future.
Cost & Performance Optimization ▾

How does 62202 bearing cost compare to alternatives?

62202 bearings offer excellent value with 780.3kg (7.65kN) load capacity at competitive pricing, providing 3-10x longer lifespan than budget alternatives.
Why This Matters
Total cost of ownership includes initial cost, maintenance, replacement frequency, and downtime costs.
How To Handle It
Calculate total cost of ownership, consider quality vs. price trade-offs, and invest in proper installation and maintenance.
High-quality bearings like 62202 typically cost 20-30% more but last 3-10x longer than budget alternatives.

What performance benefits does 62202 bearing provide?

62202 bearings deliver high load capacity, excellent speed capability, slim-fit dimensions, and reliable performance in space-constrained applications.
Why This Matters
Performance directly impacts system efficiency, reliability, and overall productivity.
How To Handle It
Select 62202 bearings for applications requiring 15mm bore, 780.3kg (7.65kN) load capacity, and 19,000 RPM capability.
62202 bearings excel in applications requiring slim-fit design with high performance capabilities.

How can I optimize 62202 bearing performance?

Optimize performance through proper installation, adequate lubrication, contamination control, and regular maintenance practices.
Why This Matters
Optimized performance extends bearing life, reduces maintenance costs, and improves system reliability.
How To Handle It
Follow manufacturer recommendations, implement preventive maintenance, monitor operating conditions, and use quality lubricants.
Proper optimization can extend 62202 bearing service life from 20,000 to 50,000+ hours in typical applications.
ðŸ”Ĩ FAST DELIVERY

Need 62202 Bearings Today?

Get instant pricing and availability for premium 62202 bearings. Same-day dispatch available for orders before 2 PM.

⚡

Instant Quote

Real-time pricing & availability

🚀

Same Day Dispatch

Orders before 2 PM ship today

🏆

Premium Quality

ISO certified, 20+ years expertise

📞 Call Now +91-9702081858 📧 Email Quote Instant Response
RHD Bearings Your Trusted Bearing Partner
📍 203 Vihar Estate, Sakinaka, Andheri East, Mumbai 400072
OEM Sales: oemsales@rhdenterprise.in
Bulk Orders: Significant discounts available
BEARINGS